Pacific Fusion<\/a> took the wraps off its latest pulser module prototype on Tuesday, a piece of equipment that allows the company to move ahead with its demonstration fusion power plant<\/a>. Construction on the fusion power plant is expected to begin this summer.<\/p>\n Results from the shipping container-sized prototype were good enough to unlock another tranche of Pacific Fusion\u2019s Series A round, which exceeds $1 billion, the company exclusively told TechCrunch. The company did not disclose the size of the tranche. Pacific Fusion is among the best-funded fusion startups<\/a>.<\/p>\n The tranche-based model is more widely used in biotech, where it saves startups time on fundraising, allowing them to remain focused on hitting technical milestones.\u00a0<\/p>\n The funding arrangement has allowed the company \u201cto keep our heads down,\u201d Pacific Fusion CTO Keith LeChien told TechCrunch. \u201cIt means that we can lean into the future without spending 20% to 50% time constantly looking for the next piece of capital.\u201d<\/p>\n Pacific Fusion is pursuing a form of fusion power known as inertial confinement. Its reactor will use 156 pulser modules to deliver an enormous jolt of electricity to a small fuel target in the fusion chamber. That electrical pulse will create a magnetic field around the eraser-sized fuel pellet<\/a>, squeezing it until atoms inside fuse and release enormous amounts of energy.<\/p>\n The startup\u2019s next challenge will be to scale up from the sub-scale prototype to a full-size pulser module, the core component of the demonstration power plant. The company hopes that power plant will be able to produce more electricity than the facility requires to operate, a feat no one has achieved yet.<\/p>\n But because the race for fusion power is heating up, the company isn\u2019t waiting for results from a full-scale pulser module before starting work on the demonstration power plant. \u201cThe shovels go in the ground for that facility this summer,\u201d LeChien said.<\/p>\n To date, inertial confinement is the only way humans have been able to produce a controlled fusion reaction that releases more energy than was required to start it, a milestone known as scientific breakeven. And so far, only one experiment, at the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory, has been able to produce<\/a> and replicate<\/a> those results.<\/p>\n But where NIF relies on large, expensive lasers, Pacific Fusion is hoping it only needs thousands of less costly electrical switches and capacitors. Those capacitors and switches will be coordinated to generate enormous, precisely timed pulses of electricity \u2014\u00a0each about 100 nanoseconds long.\u00a0<\/p>\n Pacific Fusion\u2019s challenge is ensuring the capacitors can release their energy at precisely the right moment. If they don\u2019t, the fuel pellet won\u2019t be hit with sufficient energy to compress quickly enough to spark a fusion reaction.<\/p>\n The company\u2019s demonstration device will have 156 full-size pulser modules. Each module will contain 32 circular stages, and each stage will be ringed with 10 bricks. One brick contains two capacitors to store power and one switch to release it.\u00a0<\/p>\n The prototype pulser module that the company recently tested is about a third the size of the full module. It contains nine stages and 90 bricks, and it released 440 gigawatts of peak power in just 80 nanoseconds.<\/p>\n \u201cIt meets all our requirements for scaling up to build our big demonstration system,\u201d LeChien said.\u00a0<\/p>\n Once Pacific Fusion has its demonstration power plant ready, it intends to skip past scientific breakeven and go straight for facility breakeven, in which its demonstration device generates enough energy to power the entire facility.\u00a0<\/p>\n \u201cAny fusion approach, regardless of your specific technology, has to traverse through that,\u201d LeChien said. \u201cIt\u2019s the next tectonic milestone in fusion.\u201d<\/p>\n<\/div>\n When you purchase through links in our articles, we may earn a small commission<\/a>. This doesn\u2019t affect our editorial independence.<\/em><\/p>\n![\"A](\"https:\/\/techcrunch.com\/wp-content\/uploads\/2026\/06\/pacific-fusion-pulser-prototype-end.jpeg?w=680\")